Mcculloch D30 original... edition 1
D30 is the ancester of the 200 and 300 ...ETC....series mac saws.
Centre pull......
You needed one hand on the choke unit that is a spring loaded cup in front of the carburator????
Another hand to hold the throttle trigger.
And a THIRD HAND to crank the engine............WOWWWW!!!!!!!!!!!!!!!!!!
Wonder why it was not a big success???????
Feature: LUBRI-MAC oiling -- another McCulloch exclusive. Eliminates need for a separate oil tank. And light weight is still another value feature of these new saws--only 17 pounds." --1959 McCulloch advertisement NOTE: OIL PUMP: Manual oiler added after initial production. Oil is extracted from the crankcase and is fed to the bar as the automatic oiler but does not work unless the 10:1 oil mixture is used.
It did not have an oil tank but instead it recuperates the unused vaporized oil mixture unburned from the bottom of the crankcase and injected it through a passage towards the chain.
There was a recall on all of those saws (since it did not work properly) and the front gas tank was reduced to a double tank in order to add the manual oiler button/cap and extra oil tank. This saw survived the factory recall.
It did not have an oil tank but instead it recuperates the unused vaporized oil mixture unburned from the bottom of the crankcase and injected it through a passage towards the chain.
There was a recall on all of those saws (since it did not work properly) and the front gas tank was reduced to a double tank in order to add the manual oiler button/cap and extra oil tank. This saw survived the factory recall.
Later the centre pull assembly was removed and replaced with the oil tank. Now was born the 200 and 300....etc... series McCulloch.
Testimony: My Dad (from Ontario) just called to ask me to find some info on this saw. He said he picked one of these up and got it going, but could see no place for chain oil. He told his pals it must use crankcase oil, but they thought he was nuts. :o) He said even if it did, it wouldn't be enough oil to adequately lubricate the chain.
So I got off the phone and Googled and found your site. I just called him and read the paragraph to him over the phone. Sounds like his guess was right. His must have never been fitted with the dual tank or whatever they did to try and remedy the problem.
My Dad just turned 69 and has been logging since his teens. Still cuts wood by hand. I'm gonna have to get him to look at your collection site. I'm sure he'd recognize many of the saws.
Thanks,
Greg
MANUFACTURED BY: McCULLOCH MOTORS CORP. LOS ANGELES, CALIFORNIA, U.S.A.
INTRODUCED: May 1958
DISCONTINUED: April 1959
DISPLACEMENT: 4.9 cu. in. (80cc)
BORE: 2.125 in. (54mm)
STROKE: 1.375 in. (35mm
TYPE: Aluminum with cast iron sleeve
INTAKE:Reed valve and third port induction system
CONSTRUCTION: Die cast magnesium/aluminum alloy
MCCULLOCH D30A REVISION MODIFICATION...edition 2.
MANUFACTURED BY:McCULLOCH MOTORS CORP.LOS ANGELES, CALIFORNIA, U.S.A.
SERIES OR ASSEMBLY NUMBER:
YEAR INTRODUCED:May 1958
YEAR DISCONTINUED:April 1959
ENGINE DISPLACEMENT:4.9 cu. in. (80cc)
NUMBER OF CYLINDERS:1
CYLINDER BORE:2.125 in. (54mm)
PISTON STROKE:1.375 in. (35mm
CYLINDER TYPE:Aluminum with cast iron sleeve
INTAKE METHOD:Reed valve and third port induction system
MANUFACTURER ADVERTISED H.P.:not advertised
WEIGHT :18 lbs., powerhead only
OPERATOR CONFIGURATION:One Man operation
HANDLEBAR SYSTEM:Rigid
CHAIN BRAKE:none
CLUTCH:Centrifugal
DRIVE TYPE:Direct
CONSTRUCTION:Die cast magnesium/aluminum alloy
MAGNETO TYPE:McCulloch
CARBURETOR:McCulloch diaphragm type
MAJOR REPAIR KIT:nla
MINOR REPAIR KIT:nla
AIR FILTER SYSTEM:Flocked wire screen
STARTER TYPE:McCulloch, pinion gear type
OIL PUMP:Manual oiler added after initial production. Oil is extracted from the crankcase and is fed to the bar as the automatic oiler but does not work unless the 10:1 oil mixture is used.
OPERATING RPM:
IGNITION TIMING:fixed
BREAKER POINT SETTING:0.018 in. (located under flywheel)
FLYWHEEL/COIL AIR GAP:0.010 in. (0.25 mm)
SPARK PLUG TYPE:Champion J8J
SPARK PLUG GAP:0.025 in. (0.63mm)
CRANKSHAFT MAIN BEARINGS:Ball
FUEL TANK CAPACITY:FUEL OIL RATIO:10:1
RECOMMENDED FUEL OCTANE:Regular
MIX OIL SPECIFICATION:McCulloch two-cycle chain saw mix
CHAIN PITCH:.404 in.
CHAIN TYPE:McCulloch
BAR MOUNT PATTERN:
SHORTEST GUIDE BAR SUPPLIED:16 in. (40 cm)
LONGEST GUIDE BAR SUPPLIED:24 in. (60 cm)
COLOUR SCHEME:McCulloch Yellow enamel.
As per Mike Acres site...Comments: Rushed into production as replacement for D-30 which had serious problems with scavenging chain oiler system and the pinion type starter.
MCCULLOCH D30 RECALLED, third edition.
MAC D30
But the oiling system (supposed to collect condensate oil from the crankcase and route it to the bar) didn't provide enough oil, so a retrofitted tank and push button was added on the front of the fuel tank. And the D30 had a straight stack muffler and reed valve. Later models went to a more conventional left-mounted starter, and the bulge on top became the chain oil tank.
MANUFACTURED BY: McCULLOCH MOTORS CORP.
LOS ANGELES, CALIFORNIA, U.S.A.
INTRODUCED:May 1958 ..DISCONTINUED:April 1959 .. DISPLACEMENT:4.9 cu. in. (80cc)
BORE: 2.125 in. (54mm)
STROKE: 1.375 in. (35mm)
CYLINDER TYPE: Aluminum with cast iron sleeve
INTAKE METHOD: Reed valve and third port induction system
CONSTRUCTION: Die cast magnesium/aluminum alloy
OIL PUMP: Manual and automatic. Oil is extracted from the crankcase and is fed to the bar
